Tube Removal Tools

In addition to a tube expanders and cleaners, Airetool offers a complete line of tools for removing damaged, defective, or otherwise unwanted tubes from tube sheets or other systems.

Impact Wrenches from Airetool

Impact Wrenches

Used in the construction, maintenance, and repair of heat exchangers, boilers, and coolers. Cleco Impact Wrenches provide an industrial solution that goes hand-in-hand with Airetool tube service tools. Used to open flanges and water boxes, remove plugs in fin-fan coolers, and an array of other heavy duty applications.

Tube Pullers from Airetool

Tube Pullers

The ATP III & PATP III Pumps are engineered to deliver superior performance and durability. They work in combination with a variety of different tube pulling RAMs.

  • Pumps come mounted in a roll cage with casters and large wheels for protection and increased mobility
  • Control cables and hydraulic hoses are bundled together for greater safety
  • Hydraulic hoses have quick connect fittings for easy attachment to the pump and tube pulling ram
Series ATP III Tube Pullers from Airetool

Series ATP III Tube Pullers

  • The Airetool Model ATP III Tube Pulling Ram develops 13-3/4 tons of pulling power
  • Easily remove tubes up to 1 in. O.D. from tube sheets up to 1-1/2 in. thickness*
  • Grippers bite uniformly into the tube I.D. as the piston retracts, pulling the tube from the sheet
  • Provides a full 4-3/4 inch total pulling length through a double 2-3/8 inch pull
  • Electric switch in the handle of the ram enables the hydraulic pump to operate the ram cylinder
  • Puller reverses instantly at the end of the pulling cycle or when the trigger is released

* Puller capacity of the ATP Ram will vary with tube wall thickness, tube sheet thickness and tube material.

Series PATP III Tube Pullers from Airetool

Series PATP III Tube Pullers

  • The Airetool Model PATP III Tube Pulling Ram develops 13-3/4 tons of pulling power
  • Easily remove tubes up to 1 in. O.D. from tube sheets up to 1-1/2 in. thickness*
  • Grippers bite uniformly into the tube I.D. as the piston retracts, pulling the tube from the sheet
  • Provides a full 4-3/4 inch total pulling length through a double 2-3/8 inch pull
  • Electric switch in the handle of the ram enables the hydraulic pump to operate the ram cylinder
  • Puller reverses instantly at the end of the pulling cycle or when the trigger is released

* Puller capacity of the PATP Ram will vary with tube wall thickness, tube sheet thickness and tube material.

Series HDP III Tube Pullers from Airetool

Series HDP III Tube Pullers

For Tube Sizes 1/2" thru 1", the following accessories are required:

  • HDP 99 3055 3 Spear Adapter (2900051)
  • Tube Pulling Spear - refer to the chart below for size selection
  • Optional load cap may be required if surrounding tubes are protruding and are closely spaced

For Tube Sizes 1-1/8" thru 2-1/2", the following accessories are required:

  • HDP 99 3055 3 Spear Adapter (2900051)
  • HDP 99 Adapter Kit
  • Tube Pulling Spear
  • 5526274 HDP III Ram Kit includes:
    5526273 Ram, 5526280 Adapter Lock Assembly, and
    2900007 HDP 99 LC 1 Load Cap
Series HDQ III Tube Pullers from Airetool

Series HDQ III Tube Pullers

HDQ III Gripper-type tube puller is designed for pulling 1-1/4" thru 1-3/4" O.D. tubes in heat exchangers and fire tube boilers using HDQ Gripper Kits. This gripper-type tube puller makes tube pulling faster and easier.

Series RAV III Tube Pullers from Airetool

Series RAV III Tube Pullers

  • RAV III Semi-Continuous Tube Pulling Ram allows continuous pulling of tubes up to 1" O.D. (25.4mm)
  • Tubes over 1" O.D. have a maximum pulling length of 7" (177mm).
Series JSP Manual Tube Pullers from Airetool

Series JSP Manual Tube Pullers

Manual tube puller provides economical method for tube removal

  • For tube removal applications ranging from 1/4" to 1-1/2" O.D.
  • No external power requirement makes it ideal for field service applications
  • Manual operation with a hand wrench make the JSP easy to use
  • All components have clearly marked sizes for a quick matching of tool to job
  • Components are heat-treated high strength steel for greater durability

  Catalogs


  Other Tools

Tube Drifts and Collapsing Tools

Tube Drifts and Collapsing Tools from Airetool

For the quick removal of tube stubs from tube sheets.

  • For 1/2" — 1" (12.7 — 25.4mm) OD tubes
  • Select 01 or 06 style shanks
  • For use with Cleco CH-30 chipping hammer
  • Standard length is 6". Longer length available upon request.

Tube Drifts

Drag your finger across the table to scroll

Tube O.D. Gauge Description / Order Number
in. mm -01 Shank -06 Shank
1/2 12.7 12 TD 500 12 01 (2952840) TD 500 12 06 (2952890)
1/2 12.7 14 TD 500 14 01 (2953200) TD 500 14 06 (2953250)
1/2 12.7 16 TD 500 16 01 (2953560) TD 500 16 06 (2953610)
1/2 12.7 18 TD 500 18 01 (2953920) TD 500 18 06 (2953970)
1/2 12.7 20 TD 500 20 01 (2972633) TD 500 20 06 (2979763)
5/8 15.8 10 TD 625 10 01 (2954280) TD 625 10 06 (2954330)
5/8 15.8 12 TD 625 12 01 (2954640) TD 625 12 06 (2954690)
5/8 15.8 13 TD 625 13 01 (2954820) TD 625 13 06 (2954870)
5/8 15.8 14 TD 625 14 01 (2955000) TD 625 14 06 (2955050)
5/8 15.8 15 TD 625 15 01 (2955180) TD 625 15 06 (2955230)
5/8 15.8 16 TD 625 16 01 (2955360) TD 625 16 06 (2955410)
5/8 15.8 17 TD 625 17 01 (2955540) TD 625 17 06 (2955590)
5/8 15.8 18 TD 625 18 01 (2955720) TD 625 18 06 (2955770)
5/8 15.8 19 TD 625 19 01 (2972630) TD 625 19 06 (2979765)
5/8 15.8 20 TD 625 20 01 (2972631) TD 625 20 06 (2978637)
3/4 19.1 10 TD 750 10 01 (2956080) TD 750 10 06 (2956130)
3/4 19.1 12 TD 750 12 01 (2956440) TD 750 12 06 (2956490)
3/4 19.1 13 TD 750 13 01 (2956620) TD 750 13 06 (2956670)
3/4 19.1 14 TD 750 14 01 (2956800) TD 750 14 06 (2956850)
3/4 19.1 15 TD 750 15 01 (2956980) TD 750 15 06 (2957030)
3/4 19.1 16 TD 750 16 01 (2957160) TD 750 16 06 (2957210)
3/4 19.1 17 TD 750 17 01 (2957340) TD 750 17 06 (2957390)
3/4 19.1 18 TD 750 18 01 (2957520) TD 750 18 06 (2957570)
3/4 19.1 19 TD 750 19 01 (2972617) TD 750 19 06 (2979767)
3/4 19.1 20 TD 750 20 01 (2972618) TD 750 20 06 (2979768)
7/8 22.2 14 TD 875 14 01 (2958600) TD 875 14 06 (2958650)
7/8 22.2 15 TD 875 15 01 (29587800 TD 875 15 06 (2958830)
7/8 22.2 16 TD 875 16 01 (2958960) TD 875 16 06 (2959010)
7/8 22.2 18 TD 875 18 01 (2959320) TD 875 18 06 (2959370)
7/8 22.2 20 TD 875 20 01 (2972620) TD 875 20 06 (2979771)
1 25.4 10 TD 1000 10 01 (2959680) TD 1000 10 06 (2959730)
1 25.4 12 TD 1000 12 01 (2960040) TD 1000 12 06 (2960090)
1 25.4 13 TD 1000 13 01 (2960220) TD 1000 13 06 (2960270)
1 25.4 14 TD 1000 14 01 (2960400) TD 1000 14 06 (2960450)
1 25.4 15 TD 1000 15 01 (2960580) TD 1000 15 06 (2960630)
1 25.4 16 TD 1000 16 01 (2960760) TD 1000 16 06 (2960810)
1 25.4 17 TD 1000 17 01 (2960940) TD 1000 17 06 (2960990)
1 25.4 18 TD 1000 18 01 (2961120) TD 1000 18 06 (2961170)
1 25.4 19 TD 1000 19 01 (2972622) TD 1000 19 06 (2979773)
1 25.4 20 TD 1000 20 01 (2972623) TD 1000 20 06 (2979774)

Collapsing Tools

Drag your finger across the table to scroll

Tube O.D. Gauge Description / Order Number
in. mm -01 Shank -06 Shank
3/8 9.5 16-22 CT-375-01 (2950000) CT-375-06 (2980055)
1/2 12.7 16-22 CT-500-01 (2950030) CT-500-06 (2950080)
5/8 15.8 16-22 CT-625-01 (2950210) CT-625-06 (2950260)
3/4 19.1 16-22 CT-750-01 (2950390) CT-750-06 (2950440)
7/8 22.2 16-22 CT-875-01 (2950570) CT-875-06 (2950620)
1 25.4 16-22 CT-1000-01 (2950750) CT-1000-06 (2950800)

Cleco CH-30 Series Chipping Hammer

Chipping Hammers from Cleco and Airetool

View our full line of Cleco Pneumatic Assembly Tools

Heavy duty chipping hammer has forged steel hammer for rugged use in repair and remanufacturing of heat exchanger vessels. For use with Airetool tube drifts and collapsing tools.

  • Chisel retainer for Type-06 shank
  • Ring valve hard hitting hammer

Drag your finger across the table to scroll

Model Blows per Minute Bore in. (mm) Stroke in. (mm) Weight lbs (Kg)
CH-30-RD 1650 1-1/8 (28.5) 2-1/2 (63.5) 15 (6.8)

Tube Wall Reducing Tools (TWRT)

Tube Wall Reducing Tools from Airetool

Tube Wall Reducing Tools are used on heavy gauge tubes in order to reduce the tube wall thickness prior to removing them with a tube drift tool. Available with Morse taper shank.

Drag your finger across the table to scroll

Tube O.D. Tube Gauge Model Order Number Morse Taper* Tube Sheet Thickness**
in. mm in. mm
3/8 9.5 16 TWRT-375-16 2980132 #1 2.88 73.03
3/8 9.5 17 TWRT-375-17 2992775 #1 2.88 73.03
3/8 9.5 18 TWRT-375-18 2974712 #1 2.88 73.03
3/8 9.5 20 TWRT-375-20 2978341 #1 2.88 73.03
3/8 9.5 21 TWRT-375-21 2976259 #1 2.88 73.03
3/8 9.5 22 TWRT-375-22 2989963 #1 2.88 73.03
1/2 12.7 17 TWRT-500-17 2677209 #2 2.88 73.03
1/2 12.7 18 TWRT-500-18 2677210 #2 2.88 73.03
1/2 12.7 19 TWRT-500-19 2998102 #2 2.88 73.03
1/2 12.7 20 TWRT-500-20 2982800 #2 2.88 73.03
1/2 12.7 21 TWRT-500-21 2998103 #2 2.88 73.03
1/2 12.7 22 TWRT-500-22 2998104 #2 2.88 73.03
5/8 15.8 12 TWRT-625-12 2677216 #2 3.38 85.73
5/8 15.8 13 TWRT-625-13 2677217 #2 3.38 85.73
5/8 15.8 14 TWRT-625-14 2677218 #2 3.38 85.73
5/8 15.8 15 TWRT-625-15 2677219 #2 3.38 85.73
5/8 15.8 16 TWRT-625-16 2677220 #2 3.38 85.73
5/8 15.8 17 TWRT-625-17 2677221 #2 3.38 85.73
5/8 15.8 18 TWRT-625-18 2677222 #2 3.38 85.73
5/8 15.8 19 TWRT-625-19 2972480 #2 3.38 85.73
5/8 15.8 20 TWRT-625-20 2972479 #2 3.38 85.73
5/8 15.8 21 TWRT-625-21 2984261 #2 3.38 85.73
5/8 15.8 22 TWRT-625-22 2993158 #2 3.38 85.73
3/4 19.1 10 TWRT-750-10 2677226 #2 4.38 111.13
3/4 19.1 11 TWRT-750-11 2677227 #2 4.38 111.13
3/4 19.1 12 TWRT-750-12 2677228 #2 4.38 111.13
3/4 19.1 13 TWRT-750-13 2677229 #2 4.38 111.13
3/4 19.1 14 TWRT-750-14 2677230 #2 4.38 111.13
3/4 19.1 15 TWRT-750-15 2677231 #2 4.38 111.13
3/4 19.1 16 TWRT-750-16 2677232 #2 4.38 111.13
3/4 19.1 17 TWRT-750-17 2677233 #2 4.38 111.13

* Other shank styles available on request.

** Longer reach available on request.


Drag your finger across the table to scroll

Tube O.D. Tube Gauge Model Order Number Morse Taper* Tube Sheet Thickness**
in. mm in. mm
3/4 19.1 18 TWRT-750-18 2677234 #2 4.38 111.13
3/4 19.1 19 TWRT-750-19 2972481 #2 4.38 111.13
3/4 19.1 20 TWRT-750-20 2972482 #2 4.38 111.13
3/4 19.1 21 TWRT-750-21 2998105 #2 4.38 111.13
3/4 19.1 22 TWRT-750-22 2973036 #2 4.38 111.13
7/8 22.2 10 TWRT-875-10 2677238 #3 4.63 117.48
7/8 22.2 11 TWRT-875-11 2677239 #3 4.63 117.48
7/8 22.2 12 TWRT-875-12 2677240 #3 4.63 117.48
7/8 22.2 13 TWRT-875-13 2677241 #3 4.63 117.48
7/8 22.2 14 TWRT-875-14 2677242 #3 4.63 117.48
7/8 22.2 15 TWRT-875-15 2677243 #3 4.63 117.48
7/8 22.2 16 TWRT-875-16 2677244 #3 4.63 117.48
7/8 22.2 17 TWRT-875-17 2677245 #3 4.63 117.48
7/8 22.2 18 TWRT-875-18 2677246 #3 4.63 117.48
7/8 22.2 19 TWRT-875-19 2973201 #3 4.63 117.48
7/8 22.2 20 TWRT-875-20 2973200 #3 4.63 117.48
7/8 22.2 21 TWRT-875-21 2998106 #3 4.63 117.48
7/8 22.2 22 TWRT-875-22 2973199 #3 4.63 117.48
1 25.4 10 TWRT-1000-10 2677250 #3 4.88 123.83
1 25.4 11 TWRT-1000-11 2677251 #3 4.88 123.83
1 25.4 12 TWRT-1000-12 2677252 #3 4.88 123.83
1 25.4 13 TWRT-1000-13 2677253 #3 4.88 123.83
1 25.4 14 TWRT-1000-14 2677254 #3 4.88 123.83
1 25.4 15 TWRT-1000-15 2677255 #3 4.88 123.83
1 25.4 16 TWRT-1000-16 2677256 #3 4.88 123.83
1 25.4 17 TWRT-1000-17 2677257 #3 4.88 123.83
1 25.4 18 TWRT-1000-18 2677258 #3 4.88 123.83
1 25.4 19 TWRT-1000-19 2998107 #3 4.88 123.83
1 25.4 20 TWRT-1000-20 2974737 #3 4.88 123.83
1 25.4 21 TWRT-1000-21 2985669 #3 4.88 123.83
1 25.4 22 TWRT-1000-22 2984644 #3 4.88 123.83

600-D Air Drill

Air Drill Series 600-D from Airetool

Powerful Heavy Duty air drill recommended for use with Airetool serrating tools, push-type tube cutters, and tube wall reducing tools.

  • 4.5 Horsepower D-Handle drill provides plenty of power
  • Governed motor for consistent cutting speeds
  • Reversible support handle for added leverage
  • Optional Morse taper adapter makes it universal with tube wall reducing tools, drill bits, and reamers.

Drag your finger across the table to scroll

Model Order Number Horsepower Speed Drill Capacity Reamer Capacity Length Weight Spindle Thread Side-to-Center Air Inlet Hose Size
Hp. rpm in. mm in. mm in. mm lbs. kg in. in. mm in. mm in. mm
600 D 100 8405289 4.5 100 3/4 19.0 5/8 15.8 18.0 457.0 16.0 7.3 5/8 - 16 1.5 38.1 1/2 12.7 1/2 12.7
600 D 200 6024900 4.5 200 3/4 19.0 5/8 15.8 18.0 457.0 16.0 7.3 5/8 - 16 1.5 38.1 1/2 12.7 1/2 12.7
600 D 265 6025000 4.5 265 3/4 19.0 5/8 15.8 18.0 457.0 16.0 7.3 5/8 - 16 1.5 38.1 1/2 12.7 1/2 12.7
600 D 335 6025100 4.5 335 5/8 15.8 5/8 15.8 18.0 457.0 16.0 7.3 5/8 - 16 1.5 38.1 1/2 12.7 1/2 12.7
600 D 625 6025200 4.5 625 1/2 12.7 7/16 11.1 18.0 457.0 16.0 7.3 5/8 - 16 1.5 38.1 1/2 12.7 1/2 12.7

Airetool Cutter Feed Assist (CF)

Cutter Feed Assist from Airetool

Increase your productivity with the Airetool Cutter Feed Assist. The Cutter Feed Assist is designed to work in conjunction with Airetool PIC push-type tube cutters to reduce operator fatigue and increase productivity.

  • For use with 5/8" through 1" (15.8 — 25.4mm) PIC tube cutters
  • Powered by Cleco® DPV-135 variable speed drills to match the best cutting speed to the tube material
  • Provides constant pressure which increases durability of tool bits
  • Independent cutter bit feed trigger for operator safety
  • Positive-feed stop controls tube cutting depth
  • Compact design allows the Cutter Feed Assist easier access to confined areas.

Two Models Available:

Drag your finger across the table to scroll

Part Number Order Number RPM
CF-150/500 5523443 150-500
CF-400/1200 5523444 400-1200

How To Order:

See the selection chart below*. Select the Airetool Cutter Feed Assist that corresponds to tube sizes and tube material.

Drag your finger across the table to scroll

Tube Material Tube O.D.
5/8" (16mm) 3/4" (19mm) 7/8" (22mm) 1" (25mm)
Aluminum CF-400/1200 CF-400/1200 CF-400/1200 CF-400/1200
Brass CF-4001200 CF-400/1200 CF-400/1200 CF-400/1200
Copper CF-400/1200 CF-400/1200 CF-400/1200 CF-400/1200
Carbon Steel CF-400/1200 CF-400/1200 CF-400/1200 CF-400/1200
Stainless CF-150/500 CF-150/500 CF-150/500 CF-150/500
Titanium CF-150/500 CF-150/500 CF-150/500 CF-150/500

* Refer to the Machinery’s Handbook for actual recommended tube cutting speeds for specific materials.


Airetool PIC Internal Tube Cutters

Internal Tube Cutters from Airetool

The "PIC" internal tube cutters are an economical solution to low volume tube cutting of various tube materials. Optimum tube cutting performance and tooling life are obtained when the Airetool CF Series cutter feed assist is used to match the cutting speed to the tube material.

Available for tube sizes 5/8" — 1-1/4" OD (15.8 — 31.8mm)

  • Two-piece construction allows for quick and easy tool bit replacement.
  • Cutter bits are now available with TiN coating, increasing the cutter bit life.
  • Airetool PIC tube cutters are sold with a complete set of pilots and two spare tool bit sets
  • Larger sizes and longer reaches available upon request.

Drag your finger across the table to scroll

Tube O.D. PIC Tube Cutter Reach* Pilots (incl.)
in. mm Standard "A" "C" (gauge)
1/2 12.70 PIC 500 (5519733)  PIC 500 A  PIC 500 C 18 - 20
5/8 15.88 PIC 625 (5515553) PIC 625 A (5515557) PIC 625 C (5515559) 16 - 20
3/4 19.05 PIC 750 (5515560) PIC 750 A (5515540) PIC 875 C (5515566PT)  14 - 20
7/8 22.22 PIC 875 (5515562)  PIC 875 A (5515564PT) PIC 1000 C (5515554) 15 - 20
1 25.4 PIC 1000 (5515567)  PIC 1000 A (5515568) PIC 750 C (5515514)  12 - 20
1-1/8 28.57 PIC 1125 (5515820) PIC 1125 A PIC 1125 C 14, 16, 18
1-1/4 31.75 PIC 1250 (5518134PT) PIC 1250 A PIC 1250 C 14, 16, 18

* Standard Reach = 1-11/16" to 4-7/16" (43 to 110mm)

"A" Reach = 4-11/16" to 7-7/16" (119 to 189mm)

"C" Reach = 8-3/16" to 10-15/16" (208 to 278mm)


Diagram of Internal Tube Cutters from Airetool

Drag your finger across the table to scroll

Item Number Description 5/8" (16mm) 16-20GA 3/4" (19mm) 14-20GA 7/8" (22mm) 16-20GA 1" (25mm) 12-20GA
Part No. (Order No.) Part No. (Order No.) Part No. (Order No.) Part No. (Order No.)
  Complete PIC Cutter* PIC-625 (5515553) PIC-750 (5515560) PIC-875 (5515562) PIC-1000 (5515567)
1 Pilot TTC 6 (2675000) TTC-6-14 (2668900) TTC-56-15 (2676400) TTC-36-12 (2672500)
1 Pilot TTC-46-18 (2675100) TTC-6-15 (2669000) TTC-56-16 (2990534) TTC-36-13 (2672600)
1 Pilot TTC-46-19 (2675200) TTC-6-16 (2669100) TTC-56-17 (2990535) TTC-36-14 (2672700)
1 Pilot TTC-46-20 (2675300) TTC-6-17 (2669200) TTC-56-18 (2676500) TTC-36-15 (2672800)
1 Pilot TTC 46 22 (2974902) TTC-6-18 (2669300) TTC-56-19 (2676600) TTC-36-16 (2672900)
1 Pilot TTC 46 23 (2976001) TTC-6-19 (2669400) TTC-56-20 (2676700) TTC-36-17 (2673000)
1 Pilot TTC 46 24 (2976002) TTC-6-20 (2669500)   TTC-36-18 (2673100)
1 Pilot       TTC-36-19 (2673200)
1 Pilot       TTC-36-20 (2673300)
2 Body Tip IC-41 (2979725) IC-1 (2979306) IC-51 (2979726) IC-31 (2979419)
3 Tool Bit* (Non-ferrous) TTC-43 (5338869) TTC-3 (5338865) TTC-53 (5338871) TTC-33 (5338867)
3 Tool Bit* (Ferrous) TTC-43-S (5338870) TTC-3-S (5338866) TTC-53-S (5338872) TTC-33-S (5338868)
3 Tool Bit* (Stainless) TTC-43-SS (5518303) TTC-3-SS (5517614) TTC-53-S (5517757) TTC-33-SS (5516337)
4 Mandrel Tip IC-44-T (2979724) IC-4-T (2979308) IC-34-T (2979409) IC-34-T (2979409)
5 Body Extension IC-41X (2979688) IC-1X (2979672) IC-51X (2979692) IC-31X (2979680)
6 Mandrel E xtension IC-4X (2979676) IC-4X (2979676) IC-34X (2979684) IC-34X (2979684)
7 Thrust Body TTC-47 (2675400) TTC-7 (2669600) TTC-57 (2676800) TTC-37 (2673300)
8 Bearing TTC-9 (2670000) TTC-9 (2670000) TTC-39 (2673800) TTC-39 (2673800)
9 Thrust Spring TTC-10 (2670100) TTC-10 (2670100) TTC-40 (2673900) TTC-40 (2673900)
10 Set Screw 10-32X1/4 (8000800) 10-32X1/4 (8000800) 10-32X1/4 (8000800) 10-32X1/4 (8000800)
11 Thrust Nut TTC-48 (2675700) TTC-8 (2669900) TTC-58 (2677100) TTC-38 (2673700)
12 Spring Housing PIC-21 (2979752) PIC-21 (2979752) PIC-21 (2979752) PIC-21 (2979752)
13 Spring PTC-5 (2574180) PTC-5 (2574180) PTC-5 (2574180) PTC-5 (2574180)
14 Driver PIC-4 (2979751) PIC-4 (2979751) PIC-4 (2979751) PIC-4 (2979751)

* Standard length listed


Air Driven Tube Cutter (TIC)

Air Driven Tube Cutters from Airetool

Complete tube cutting system for various tube materials. Five models available in speeds from 100 to 625 rpm for various steel and non-ferrous tube applications.

  • Powerful, 4.5 Horsepower motor with D-handle
  • Governed motor for consistent cutting speeds
  • Positive lever-operated feed of cutter bit
  • One mandrel drive adapter works with all sizes of cutters (TTC-30, ordering number 2671400)

Drag your finger across the table to scroll

RPM Tube Material Cutter Complete
5/8" O.D. 3/4" O.D. 7/8" O.D. 1" O.D.
Pneumatic Models
625 Non-ferrous TIC-625-625 (5515586) TIC625-750 (5515590) TIC-625-875 (5515594) TIC-625-1000 (5515598)
335 Non-ferrous/Ferrous TIC-350-625 (5515602) TIC-350-750 (5515606) TIC-350-875 (5515610) TIC-350-1000 (5515614)
265 Ferrous-Stainless TIC-265-625 (5515618) TIC-265-750 (5515622) TIC-265-875 (5515626) TIC-265-1000 (5515630)
200 Ferrous-Stainless TIC-200-625 (5518909) TIC-200-750 (5518459) TIC-200-875 (5522345) TIC-200-1000 (5519460)
100 Stainless & Titanium TIC-100-625 (5519526) TIC-100-750 (5517806) TIC-100-875 (5522125) TIC-100-1000 (5518512)
40 Titanium & Inconel TIC-40-625 (5521860) TIC-40-750 (5518184) TIC-40-875 TIC-40-1000

Electric Tube Cutter (EIC)

Electric Tube Cutters from Airetool

Where compressed air supply is unavailable, the EIC tube internal tube cutter will perform satisfactorily for low volume tube cutting jobs. The variable speed motor can be used to cut various steel and non-ferrous tube materials.

  • Powerful, 120VAC, 7 amp reversible motor
  • Trigger speed control: 0 - 600 RPM
  • Triple gear reduction provides abundant torque output
  • One mandrel drive adapter works with all sizes of cutters (ETC-30, ordering number 3073240)

Drag your finger across the table to scroll

RPM Tube Material Cutter Complete
5/8" O.D. 3/4" O.D. 7/8" O.D. 1" O.D.
Electric Models
EIC 100/600 RPM Non-ferrous
Ferrous
Stainless
Titanium
Inconel
EIC 100/600 625 (5515772) EIC 100/600 750 (5515635) EIC 100/600 875 (5523035) EIC 100/600 1000 (5518583PT)

Cutter Bodies Complete for TIC & EIC Models

Several design improvements have been incorporated for maintenance and increased service life

  • Shorter and stronger cutter body improves durability and increases bit life
  • Cutter body is threaded into body extension for easier bit replacement
  • Standard mandrel driver fits all sizes of Airetool tube cutters
  • Adjustable reach "IC" cutter bodies:
    Standard reach 1-11/16" to 4-7/16" (42 - 112mm)
    "A" reach = 4-11/16" to 7-7/16" (112 - 188mm)
    "C" reach = 8-3/16" to 10-15/16" (207 - 277mm)
  • Larger sizes and longer lengths available upon request.

Drag your finger across the table to scroll

Description Tube O.D.
5/8" O.D. 3/4" O.D. 7/8" O.D. 1" O.D.
Tube Cutter body Sub-assemblies for TIC & EIC models
Cutter Body Complete IC-625 (5515574) IC-750 (5515577) IC-875 (5515581) IC-1000 (5515571)
Tool Bit* (Non-ferrous) TTC-43 (5338869) TTC-3 (5338865) TTC-53 (5338871) TTC-33 (5338867)
Tool Bit* (Ferrous) TTC-43-S (5338870) TTC-3-S (5338866) TTC-53-S (5338872) TTC-33-S (5338868)
Tool Bit* (Stainless) TTC-43-SS (5518303) TTC-3-SS (5517614) TTC-53-SS (5517757) TTC-33-SS (5516337)

* Tool Bit part numbers above consist of 2 bits each.

Tube Cutter Bodies consist of all parts necessary to convert models TIC & EIC to different tube size.

Specify desired reach:

  • Standard Reach 4-7/16" (112.7mm) shown
  • "A" Reach 7-7/16" (188.9mm)
  • "C" Reach 10-15/16" (277.8mm)

RCM One Revolution Tube Cutters

RCM One Revolution Tube Cutters from Airetool

For cutting tubes beyond the tube sheet in heat exchangers, condensers, and boilers. RCM series tube cutters are also an excellent tool for puncturing defective tubes prior to tube plugging. This reduces the risk of pressure buildup in plugged tubes.

  • Designed for hand use by employing a ratchet or hand wrench for manual operation
  • Available in standard reaches of 6" (152mm) and 10" (254mm)
  • Longer reaches are available in 10" increments upon request

Drag your finger across the table to scroll

Tube O.D. BWG Tube I.D. Tool Reach Cutting Bit
in. mm 6" (152.4mm) 10" (254.0mm)
1/2 12.70 18-19 .400"-420" 10.2-10.7mm RCM-105 (5522994) RCM-105-10 (5523116) RC-500-2 (2993368)
1/2 12.70 20 .430"-.450" 11.0-11.3mm RCM-110 (5522929) RCM-110-10  RC-500-2 (2993368)
5/8 15.88 14 .450"-.470" 11.4-11.9mm RCM-115 (5522995) RCM-115-10 (5523118) RC-625-2 (2993372)
5/8 15.88 15-16 .472"-.510" 12-12.9mm RCM-120 (5522930) RCM-120-10 (5523119) RC-625-2 (2993372)
5/8 15.88 17-18 .500"-531" 12.7-13.5mm RCM-130 (5522931) RCM-130-10 (5523120) RC-625-2 (2993372)
5/8 15.88 19-20 .531"-.560" 13.5-14.2mm RCM-135 (5522996) RCM-135-10 (5523121) RC-625-2 (2993372)
5/8 15.88 22 .550"-.580" 14.0-14.7mm RCM-140 (5522932) RCM-140-10 (5524952) RC-625-2 (2993372)
3/4 19.05 12-13 .530".560" 13.5-14.2mm RCM-135-3/4 (5523115) RCM-135-3/4-10 (5526397) RC-750-2A (2995865)
3/4 19.05 14-15 .580"-610" 14.7-15.5mm RCM-150 (5522933) RCM-150-10 (5523123) RC-750-2 (2993374)
3/4 19.05 16 .600"-630" 15.2-16.0mm RCM-155 (5522997) RCM-155-10 (5523124) RC-750-2 (2993374)
3/4 19.05 17-18 .625"-.650" 15.9-16.5mm RCM-160 (5522934) RCM-160-10 (5523125) RC-750-2 (2993374)
3/4 19.05 19-20 .660"-.690" 16.7-17.5mm RCM-170 (5522935) RCM-170-10 (5523126PT) RC-750-2 (2993374)
7/8 22.22 14-15 .700"-.730" 17.8-18.5mm RCM-180 (5522936) RCM-180-10 (5523127) RC-875-2 (2993384)
7/8 22.22 16-17 .740"-.770" 18.8-19.5mm RCM-190 (5522937) RCM-190-10 (5523128) RC-875-2 (2993384)
7/8 22.22 18 .760"-.790" 19.3-20.0mm RCM-195 (5522998) RCM-195-10 (5524478) RC-875-2 (2993384)
7/8 22.22 19-20 .780"-810" 19.8-20.6mm RCM-200 (5522938) RCM-200-10 (5523241PT) RC-875-2 (2993384)
1 25.40 12 .760"-.790" 19.3-20.0mm RCM-195 (5522998) RCM-195-10 (5524478) RC-875-2 (2993384)
1 25.40 14 .820"-.850" 20.8-21.6mm RCM-210 (5522939) RCM-210-10 (5523131) RC-1000-2 (2993394)
1 25.40 15 .840"-.870" 21.3-22.1mm RCM-215 (5522999) RCM-215-10 (5523132) RC-1000-2 (2993394)
1 25.40 16-17 .860"-.890" 21.8-22.6mm RCM-220 (5522940) RCM-220-10 (5523133) RC-1000-2 (2993394)

Drag your finger across the table to scroll

Tube O.D. BWG Tube I.D. Tool Reach Cutting Bit
in. mm 6" (152.4mm) 10" (254.0mm)
1 25.40 18-19 .890"-910" 22.6-23.1mm RCM-230 (5522941) RCM-230-10 (5523134) RC-1000-2 (2993394)
1 25.40 22 .940"-970" 23.9-24.6mm RCM-240 (5522942) RCM-240-10 (5525584) RC-1000-2 (2993394)
1-1/4 31.75 12 1.020"-1.050" 25.9-26.7mm RCM-260 (5523000) RCM-260-10 (5523136) RC-1250-2 (2993404)
1-1/4 31.75 13-14 1.050"-1.080" 26.7-27.4mm RCM-270 (5523001) RCM-270-10 (5523137) RC-1250-2 (2993404)
1-1/4 31.75 15-16 1.100"-1.130" 27.9-28.7mm RCM-280 (5523002) RCM-280-10 (5523138) RC-1250-2 (2993404)
1-1/4 31.75 17-19 1.130"-1.160" 28.7-29.6mm RCM-290 (5523003) RCM-290-10 (5523139) RC-1250-2 (2993404)
1-3/8 34.93 13-14 1.180"-1.210" 30-30.7mm RCM-300 (5523709) RCM-300-10 (5525838) RC-1500-2 (2993417)
1-1/2 38.10 12-13 1.280"-1.310" 32.5-33.3mm RCM-330 (5523004) RCM-330-10 (5523140) RC-1500-2 (2993417)
1-1/2 38.10 14-15 1.330"-1.360" 33.8-34.5mm RCM-340 (5523005) RCM-340-10 (5523005) RC-1500-2 (2993417)
1-1/2 38.10 16-17 1.360"-1.390" 34.5-35.3mm RCM-350 (5523006) RCM-350-10 (5523142) RC-1500-2 (2993417)
1-1/2 38.10 18-19 1.390"-1.420" 35.3-36.1mm RCM-360 (5523007) RCM-360-10 (5523143) RC-2000-2 (2993427)
2 50.80 12-13 1.770"-1.810" 45.0-46.0mm RC-2012 (5521677) RC-2012-10 RC-2000-2 (2993427)
2 50.80 14-15 1.820"-1.860" 46.2-47.2mm RC-2014 (5521678PT) RC-2014-10 RC-2000-2 (2993427)
2 50.80 16-17 1.860"-1.900" 46.2-48.2mm RC-2016 (5521679) RC-2016-10 RC-2000-2 (2993427)
2 50.80 18-19 1.890"-1.930" 48.0-49.0mm RC-2018 (5521680) RC-2018-10 RC-2000-2 (2993427)
2-1/2 63.50 12-13 2.270"-2.310" 57.6mm-58.6 RC-2512 (5521681) RC-2512-10 RC-2000-2 (2993427)
2-1/2 63.50 14-15 2.320"-2.360" 58.9-60.0mm RC-2514 (5521682) RC-2514-10 RC-2000-2 (2993427)
2-1/2 63.50 16-17 2.360"-2.400" 60.0-61.0mm RC-2516 (5521683) RC-2516-10 RC-2000-2 (2993427)
2-1/2 63.50 18-19 2.390"-2.430" 60.7-61.7mm RC-2518 (5521684) RC-2518-10 RC-2000-2 (2993427)